Product Description
DESIGN HIGHLIGHTS
The PondMAX EvoII Submersible Pumps have been manufactured with advanced technology to provide you with the best quality pumps for your pond or water feature. Visit our website to view our range of pond filtration, outdoor/ underwater lighting, water treatments and general accessories.
• Variable Frequency Motor Technology – Extra high speed rotations of impellor.
• Open Vane Impellor Design – Handles large particles size up to 4mm soft sediment.
• Long life Impellor Design – Ceramic shaft is wear resistant and self-lubricated by water
• High Head Pressure – Due to extra high speed rotations of impellor.
• Energy Efficient – Exceptional low power consumption to high water flow conversion.
• Eco Friendly – Exceptional low dB noise rating with low mechanical vibration.
• Marine Compatible* see warranty disclaimer – No exposed copper.
• Tool-less Assembly - For easy maintenance. No special tools required.
• Rotor Stop Protection – Sensors automatically cut power in the event that the impellor stops rotating, reducing the chances of motor burnout.
• Soft Start – Rotor starts at low speed and increases over a short period of time. This reduces sudden recoil kick back on start up.
BENEFITS INCLUDE
• PondMAX Fountain & Pond pumps are suitable for use in many different applications including fountains, water features, aquatic systems, aquarium applications and hydroponics. The pumps can be used in either submersible or in-line use applications.
• Submersible pumps are a magnetically driven centrifugal pump, therefore they cannot suck from a water level that is below the inlet level when used in-line.
• Your pump has a single moving part (an impellor set) enabling easy cleaning and maintenance.
• The models EV1900 – EV13600 Pumps have intelligent circuitry that analyses the speed and torque of the motor. It will increase and decrease the energy usage to maximise efficiency. The soft start nature of the system helps to avoid sudden jolting at start up. The intelligent system will change the motor speed to maximise the flow of water in the given circumstances. If the impellor gets jammed or stops, the circuitry will sense the state and cut the power automatically for 3 seconds and then power up again. This procedure will repeat 3 times. If the rotor is still jammed, it will activate a prolonged low state, till the pump is turned off, and adequate maintenance is carried out. Thus minimising motor burnout, due to electrical heat, through lack of water flow through the motor.
• The motor and electrical components are totally encapsulated in epoxy resin, ensuring safe operation under water.
• The pump has a robust bearing and shaft design so no oil/grease lubrication is required.
• PondMAX pumps, that have plastic impeller parts and ceramic shafts, can be used in Marine applications as there is no exposed copper. For Marine use, please see warranty disclaimer.
• PondMAX Submersible Pumps are continuous rated therefore are designed to operate 24/7.
• An optional fountain kit can be purchased and fitted to the models EV650 – EV4900 pumps. Some of these models include a sponge pre-filter that assists in straining the partials in the water, to assist the fountain nozzles becoming blocked up with debris. See your retailer for options.
PRODUCT SPECIFIC SAFEGUARDS
• Do not operate the pump without water at any time, permanent damage may occur.
• Be sure the equipment is submerged completely in the water. The depth should not be greater than 2m. If used in line, the pump must have adequate flooded suction at all times.
• The pump is designed to be used in a garden pond/ waterfeature or Aquarium environment. It is not to be used in any other manner or purpose.
• The pump should only be used in clean water. Do not use the pump in, or with, any chemicals such as a solvent or gasoline.
• All PondMAX Submersible pumps are cooled by water flowing through the inside of the motor body. If the pump flow becomes restricted it will overheat and could cause permanent damage. Large tubing size is strongly recommended to deliver adequate water flow to cool the pump.
• The pump needs to be cleaned regularly to prevent the pump becoming blocked, thus causing the pump to overheat and burn out. This is not a warrantable event. It is strongly recommended not to select a pump that is too small for the job required. The flow rate through the pump needs to be enough so that a half of the rated max flow is kept running at all times.
Downloads:
